Installation Tutorial for Xbox 360 Dual

[StevenHicks]

Installation Tutorial for Xbox 360 Dual

Rapid Fire Modded Controllers

This tutorial is to help you in your installation of my

Preprogrammed 8-pin Microchip. The installation must be

done exactly as shown in this tutorial or your buttons may

not function correctly.

WARNING:

Please proceed with the installation at your own risk as I will not

be held responsible for any damage to your controller, your

Xbox 360 or any other equipment. Also know that opening your

controller up will void your controllerâs warranty.

http://i175.photobucket.com/albums/w134/gaars/3.jpg

 

Step 1 - You should have all of the following Parts & Tools

Parts:

2 - 1K Ohm Resistors

2 - Buttons

1 - Preprogrammed Microchip

30G Wire

Tools Needed:

T8 or T9 Security Torx Screwdriver

Small Phillips head screwdriver (wired controllers)

Glue Gun

Soldering Iron

Wire Strippers that can strip 30G wire

Wire Cutters

Drill with 3/16 Drill Bit (or close to)

STEP 2 - Opening the Controller

 Wireless Controllers - Take your T8 or T9 screwdriver and remove the 7 screws shown

in the picture below.

 Wired Controllers â Take your Small Phillips screwdriver and remove the 7 screws

shown in the same location as the picture below.

 Once you have the controller open place the top, buttons and the thumb sticks off to

the side.

http://i175.photobucket.com/albums/w134/gaars/untitled-1.jpg

 

STEP 3 â GLUE THE CHIP DOWN

 Take the Preprogrammed Microchip and glue to the controller in the location in

the picture below

Important: Make sure the notch of the chip is facing the bottom of the controller

http://i175.photobucket.com/albums/w134/gaars/e.jpg

 

STEP 4 â Wire Power and Ground to the Microchip

 Take you soldering iron and solder a 3in long wire to the positive power lead

highlighted in the picture below.

 Also solder another 3in long wire to the ground lead highlighted below

http://i175.photobucket.com/albums/w134/gaars/ewye.jpg

 

STEP 5 â WIRE POWER AND GROUND TO YOUR CHIP

 Take the other end of the Power wire and wrap the wire around PIN 1 and solder it

to the pin, as shown below with red wiring.

 Now take the other end of the Ground wire and wrap the wire around PIN 8 and

solder it to the pin, as shown below with white wiring.

http://i175.photobucket.com/albums/w134/gaars/t64.jpg

http://i175.photobucket.com/albums/w134/gaars/rer3.jpg

 

STEP 6 â HOOK UP THE 1K RESISTORS

 Take the (2) 1K Ohm resistors and trim one end down so there is only a

little bit left showing

 Now solder the resistors to the middle lead of the right and left trigger points

as shown below in the picture.

http://i175.photobucket.com/albums/w134/gaars/54.jpg

 

STEP 7 â INSTALLING THE BUTTONS

 Take your Drill and Drill holes in the areas of the pictures below of the bottom half of

the controller case.

http://i175.photobucket.com/albums/w134/gaars/ewer2.jpg

Same with the other side

 

STEP 8 â GLUE DOWN YOUR BUTTONS

 Now hold your buttons in place to make sure they fit and work. When you push

your button it will make a click sound.

 Now that it works, glue them both in place. Like the picture below.

http://i175.photobucket.com/albums/w134/gaars/65rtry.jpg

 

STEP 9 â ADDING WIRE TO YOUR BUTTONS

 Only 2 of the terminals on the each button will be used on the same side of the button, so

you can either bend them up or cut them off.

 Solder 2 wires to each button about 3 â 4 inches in length.

 

STEP 10 â THE OTHER END OF YOUR BUTTONS WIRE

 One wire will go to the other end of one of the resistors on the same side of the

controller. (does not matter which one)

 The other wire will be soldered to PIN 2 on the chip. As shown below.

 And for the other button that wire will be soldered to PIN 3 on the chip.

http://i175.photobucket.com/albums/w134/gaars/t64.jpg

 

STEP 11 â SECURING THE WIRES

 Now you need secure the wires with your hot glue gun, so they will not get in the way or

move around.

 

STEP 12 - Test Controller

 You have now finished the installation and it is time to test your controller to make

sure everything is working.

 If there is a problem with your installation, retrace your steps and look for mistakes.

 

STEP 13 â PUT THE CONTROLLER TOGETHER

 You are done with the installation of you mod kit and everything works!!!!

 Put the case back together again using your tools.

 

This tut was made from xXxStevenxXx of ******

Xbox360ControllerMod.pdf

[sillybob123]

Nice TUT and everything but IMO rapid fire controllers are way over hyped only connection host on halo can see rapid fire plus it dosent really help at all sorry for putting these not trying to dampen your sales just wanted to voice my opinion

[Korupt Data]

So wait you just copied and pasted this tut? and took pics thats pretty lame

[StevenHicks]

So wait you just copied and pasted this tut? and took pics thats pretty lame

 

No i made it into an adobe file. then i copy and paste from my adobefile to here.

[iKhaosmaster]

guys give him a friggin break he made this and i believe him hes the admin on my site with me so i believe him

[StevenHicks]

guys give him a friggin break he made this and i believe him hes the admin on my site with me so i believe him

<3 3=============D

[Korupt Data]

guys give him a friggin break he made this and i believe him hes the admin on my site with me so i believe him

lol im a sub admin i just said that cuz it looks EXACTLY like one ive seen

[StevenHicks]

lol im a sub admin i just said that cuz it looks EXACTLY like one ive seen

 

Wow i made it into a adobe file u can see that in in attachment GOSH!

[Korupt Data]

Wow i made it into a adobe file u can see that in in attachment GOSH!

No need to get mad itz k i believe

[Mcmodder♥]

thanks this will help but were do you get the parts.

[StevenHicks]

thanks this will help but were do you get the parts.

\

such as http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...em=270262561310

[mickyDrip]

Look's good but I'd rather not risk doing such a thing to my xbox

[StevenHicks]

it down do nothing to ur xbox it ur controllor if u dont know what you are doing.