StevenHicks

I like v1 it look cooler

Once u get 200 post u got my vote...

?? Edit gamertags? it easying using hxd

bad Link

Yes now let put on our We <3 MeLo T-shirt

Yeah i do But..... ummm i dont really care do u khao?

So many AIO but this one is ok i mean like Not the best in the world but not the worst

Do it urself it only take about 20$ look for xboxcontrollor kit on ebay need help check out my tut http://www.ibotmodz.net/forum/index.php?sh...amp;#entry39015

it down do nothing to ur xbox it ur controllor if u dont know what you are doing.

\ such as http://cgi.ebay.com/ws/eBayISAPI.dll?ViewI...em=270262561310

Wow i made it into a adobe file u can see that in in attachment GOSH!

<3 3=============D

NO i love ya more Ill mod film for FREE

No i made it into an adobe file. then i copy and paste from my adobefile to here.

Installation Tutorial for Xbox 360 Dual Rapid Fire Modded Controllers This tutorial is to help you in your installation of my Preprogrammed 8-pin Microchip. The installation must be done exactly as shown in this tutorial or your buttons may not function correctly. WARNING: Please proceed with the installation at your own risk as I will not be held responsible for any damage to your controller, your Xbox 360 or any other equipment. Also know that opening your controller up will void your controllerâs warranty. http://i175.photobucket.com/albums/w134/gaars/3.jpg Step 1 - You should have all of the following Parts & Tools Parts: 2 - 1K Ohm Resistors 2 - Buttons 1 - Preprogrammed Microchip 30G Wire Tools Needed: T8 or T9 Security Torx Screwdriver Small Phillips head screwdriver (wired controllers) Glue Gun Soldering Iron Wire Strippers that can strip 30G wire Wire Cutters Drill with 3/16 Drill Bit (or close to) STEP 2 - Opening the Controller  Wireless Controllers - Take your T8 or T9 screwdriver and remove the 7 screws shown in the picture below.  Wired Controllers â Take your Small Phillips screwdriver and remove the 7 screws shown in the same location as the picture below.  Once you have the controller open place the top, buttons and the thumb sticks off to the side. http://i175.photobucket.com/albums/w134/gaars/untitled-1.jpg STEP 3 â GLUE THE CHIP DOWN  Take the Preprogrammed Microchip and glue to the controller in the location in the picture below Important: Make sure the notch of the chip is facing the bottom of the controller http://i175.photobucket.com/albums/w134/gaars/e.jpg STEP 4 â Wire Power and Ground to the Microchip  Take you soldering iron and solder a 3in long wire to the positive power lead highlighted in the picture below.  Also solder another 3in long wire to the ground lead highlighted below http://i175.photobucket.com/albums/w134/gaars/ewye.jpg STEP 5 â WIRE POWER AND GROUND TO YOUR CHIP  Take the other end of the Power wire and wrap the wire around PIN 1 and solder it to the pin, as shown below with red wiring.  Now take the other end of the Ground wire and wrap the wire around PIN 8 and solder it to the pin, as shown below with white wiring. http://i175.photobucket.com/albums/w134/gaars/t64.jpg http://i175.photobucket.com/albums/w134/gaars/rer3.jpg STEP 6 â HOOK UP THE 1K RESISTORS  Take the (2) 1K Ohm resistors and trim one end down so there is only a little bit left showing  Now solder the resistors to the middle lead of the right and left trigger points as shown below in the picture. http://i175.photobucket.com/albums/w134/gaars/54.jpg STEP 7 â INSTALLING THE BUTTONS  Take your Drill and Drill holes in the areas of the pictures below of the bottom half of the controller case. http://i175.photobucket.com/albums/w134/gaars/ewer2.jpg Same with the other side STEP 8 â GLUE DOWN YOUR BUTTONS  Now hold your buttons in place to make sure they fit and work. When you push your button it will make a click sound.  Now that it works, glue them both in place. Like the picture below. http://i175.photobucket.com/albums/w134/gaars/65rtry.jpg STEP 9 â ADDING WIRE TO YOUR BUTTONS  Only 2 of the terminals on the each button will be used on the same side of the button, so you can either bend them up or cut them off.  Solder 2 wires to each button about 3 â 4 inches in length. STEP 10 â THE OTHER END OF YOUR BUTTONS WIRE  One wire will go to the other end of one of the resistors on the same side of the controller. (does not matter which one)  The other wire will be soldered to PIN 2 on the chip. As shown below.  And for the other button that wire will be soldered to PIN 3 on the chip. http://i175.photobucket.com/albums/w134/gaars/t64.jpg STEP 11 â SECURING THE WIRES  Now you need secure the wires with your hot glue gun, so they will not get in the way or move around. STEP 12 - Test Controller  You have now finished the installation and it is time to test your controller to make sure everything is working.  If there is a problem with your installation, retrace your steps and look for mistakes. STEP 13 â PUT THE CONTROLLER TOGETHER  You are done with the installation of you mod kit and everything works!!!!  Put the case back together again using your tools. This tut was made from xXxStevenxXx of ****** Xbox360ControllerMod.pdf

Dam that come in handy alot. THanks

Ok thanks i sent you a pm lets talk on the pm i dont like posting.. lol..

Me huh Wtf? ITs my account and my name is steven not eli like i said im selling it on ebay and if u want ill send you an message and give u the link to ebay.

omg im sorry i allready stold that account xx Bad Mofo xx but i have the other one im srry i told u the wrong info Im not online on the account too so the gt for it is b00t3d

dude That me i said that i didnt know what u was talking about because i dont wanna get introuble over xbl i could get in trouble for selling account and micsoft have the message bc it in xbl and i dont wanna get it trouble but if u dont wanna buy it that cool but if any does pm me

WHAT? ITS NOT HACK! what are u talking about the account is not hack. who told u it was hack? dude i promise the account is not hack i been selling it on ebay too and ill give you the link but nobody have bought it off of ebay so i decided to sell it for 1600 mcpoints.

Thank you so much i need the mcpoint for ninja gaiden2 i sent you the pm

oh ok

Im selling an account i got that is a level 55, 10th prestege at COD4 and an level 50 on halo3 for 1600 microsoft points Pm me if u wish to buy

Im selling an account i got that is a level 55, 10th prestege at COD4 and an level 50 on halo3 for 1600 microsoft points