Jump to content

  •  

  • iBotModz CBox


    Photo

    Installation Tutorial for Xbox 360 Dual


    • Please log in to reply
    12 replies to this topic

    #1 StevenHicks

    StevenHicks

      Private

    • Members+

    • 25 posts
    • Joined: 16-July 08

    Posted 06 August 2008 - 04:50 PM

    Installation Tutorial for Xbox 360 Dual
    Rapid Fire Modded Controllers
    This tutorial is to help you in your installation of my
    Preprogrammed 8-pin Microchip. The installation must be
    done exactly as shown in this tutorial or your buttons may
    not function correctly.
    WARNING:
    Please proceed with the installation at your own risk as I will not
    be held responsible for any damage to your controller, your
    Xbox 360 or any other equipment. Also know that opening your
    controller up will void your controllerâ??s warranty.
    Posted Image

    Step 1 - You should have all of the following Parts & Tools
    Parts:
    2 - 1K Ohm Resistors
    2 - Buttons
    1 - Preprogrammed Microchip
    30G Wire
    Tools Needed:
    T8 or T9 Security Torx Screwdriver
    Small Phillips head screwdriver (wired controllers)
    Glue Gun
    Soldering Iron
    Wire Strippers that can strip 30G wire
    Wire Cutters
    Drill with 3/16 Drill Bit (or close to)
    STEP 2 - Opening the Controller
     Wireless Controllers - Take your T8 or T9 screwdriver and remove the 7 screws shown
    in the picture below.
     Wired Controllers â?? Take your Small Phillips screwdriver and remove the 7 screws
    shown in the same location as the picture below.
     Once you have the controller open place the top, buttons and the thumb sticks off to
    the side.
    Posted Image

    STEP 3 â?? GLUE THE CHIP DOWN
     Take the Preprogrammed Microchip and glue to the controller in the location in
    the picture below
    Important: Make sure the notch of the chip is facing the bottom of the controller
    Posted Image

    STEP 4 â?? Wire Power and Ground to the Microchip
     Take you soldering iron and solder a 3in long wire to the positive power lead
    highlighted in the picture below.
     Also solder another 3in long wire to the ground lead highlighted below
    Posted Image

    STEP 5 â?? WIRE POWER AND GROUND TO YOUR CHIP
     Take the other end of the Power wire and wrap the wire around PIN 1 and solder it
    to the pin, as shown below with red wiring.
     Now take the other end of the Ground wire and wrap the wire around PIN 8 and
    solder it to the pin, as shown below with white wiring.
    Posted Image
    Posted Image

    STEP 6 â?? HOOK UP THE 1K RESISTORS
     Take the (2) 1K Ohm resistors and trim one end down so there is only a
    little bit left showing
     Now solder the resistors to the middle lead of the right and left trigger points
    as shown below in the picture.
    Posted Image

    STEP 7 â?? INSTALLING THE BUTTONS
     Take your Drill and Drill holes in the areas of the pictures below of the bottom half of
    the controller case.
    Posted Image
    Same with the other side

    STEP 8 â?? GLUE DOWN YOUR BUTTONS
     Now hold your buttons in place to make sure they fit and work. When you push
    your button it will make a click sound.
     Now that it works, glue them both in place. Like the picture below.
    Posted Image

    STEP 9 â?? ADDING WIRE TO YOUR BUTTONS
     Only 2 of the terminals on the each button will be used on the same side of the button, so
    you can either bend them up or cut them off.
     Solder 2 wires to each button about 3 â?? 4 inches in length.

    STEP 10 â?? THE OTHER END OF YOUR BUTTONS WIRE
     One wire will go to the other end of one of the resistors on the same side of the
    controller. (does not matter which one)
     The other wire will be soldered to PIN 2 on the chip. As shown below.
     And for the other button that wire will be soldered to PIN 3 on the chip.
    Posted Image

    STEP 11 â?? SECURING THE WIRES
     Now you need secure the wires with your hot glue gun, so they will not get in the way or
    move around.

    STEP 12 - Test Controller
     You have now finished the installation and it is time to test your controller to make
    sure everything is working.
     If there is a problem with your installation, retrace your steps and look for mistakes.

    STEP 13 â?? PUT THE CONTROLLER TOGETHER
     You are done with the installation of you mod kit and everything works!!!!
     Put the case back together again using your tools.

    This tut was made from xXxStevenxXx of ******

    Attached Files



    #2 sillybob123

    sillybob123

      I am a homo.

    • Members+

    • 541 posts
    • Joined: 08-May 08
    • Gender:Male
    • Location:The Computer/Xbox

    Posted 06 August 2008 - 04:55 PM

    Nice TUT and everything but IMO rapid fire controllers are way over hyped only connection host on halo can see rapid fire plus it dosent really help at all sorry for putting these not trying to dampen your sales just wanted to voice my opinion :D

    #3 Korupt Data

    Korupt Data

      SoOoO KoRuPtAbLe

    • Retired Staff

    • 3,503 posts
    • Joined: 12-May 08
    • Gender:Male
    • Location:That file you downloaded

    Posted 06 August 2008 - 06:32 PM

    So wait you just copied and pasted this tut? and took pics thats pretty lame

    #4 StevenHicks

    StevenHicks

      Private

    • Members+

    • 25 posts
    • Joined: 16-July 08

    Posted 06 August 2008 - 07:13 PM

    So wait you just copied and pasted this tut? and took pics thats pretty lame


    No i made it into an adobe file. then i copy and paste from my adobefile to here.

    #5 iKhaosmaster

    iKhaosmaster

      Yawn

    • Members+

    • 1,346 posts
    • Joined: 29-April 08
    • Gender:Male

    Posted 06 August 2008 - 07:23 PM

    guys give him a friggin break he made this and i believe him hes the admin on my site with me so i believe him

    #6 StevenHicks

    StevenHicks

      Private

    • Members+

    • 25 posts
    • Joined: 16-July 08

    Posted 06 August 2008 - 07:25 PM

    guys give him a friggin break he made this and i believe him hes the admin on my site with me so i believe him

    <3 3=============D

    #7 Korupt Data

    Korupt Data

      SoOoO KoRuPtAbLe

    • Retired Staff

    • 3,503 posts
    • Joined: 12-May 08
    • Gender:Male
    • Location:That file you downloaded

    Posted 06 August 2008 - 10:31 PM

    guys give him a friggin break he made this and i believe him hes the admin on my site with me so i believe him

    lol im a sub admin :p i just said that cuz it looks EXACTLY like one ive seen

    #8 StevenHicks

    StevenHicks

      Private

    • Members+

    • 25 posts
    • Joined: 16-July 08

    Posted 07 August 2008 - 12:44 PM

    lol im a sub admin :p i just said that cuz it looks EXACTLY like one ive seen


    Wow i made it into a adobe file u can see that in in attachment GOSH!

    #9 Korupt Data

    Korupt Data

      SoOoO KoRuPtAbLe

    • Retired Staff

    • 3,503 posts
    • Joined: 12-May 08
    • Gender:Male
    • Location:That file you downloaded

    Posted 07 August 2008 - 02:17 PM

    Wow i made it into a adobe file u can see that in in attachment GOSH!

    No need to get mad :p itz k i believe

    #10 Mcmodder♥

    Mcmodder♥

      I have no friends.

    • Banned

    • 622 posts
    • Joined: 03-August 08
    • Gender:Male
    • Location:???????

    Posted 08 August 2008 - 01:49 PM

    thanks this will help but were do you get the parts. :unsure:

    #11 StevenHicks

    StevenHicks

      Private

    • Members+

    • 25 posts
    • Joined: 16-July 08

    Posted 08 August 2008 - 07:24 PM

    thanks this will help but were do you get the parts. :unsure:

    \
    such as http://cgi.ebay.com/...em=270262561310

    #12 mickyDrip

    mickyDrip

      Corporal Grade 1

    • Members+

    • 107 posts
    • Joined: 07-August 08

    Posted 09 August 2008 - 06:30 AM

    Look's good but I'd rather not risk doing such a thing to my xbox =@

    #13 StevenHicks

    StevenHicks

      Private

    • Members+

    • 25 posts
    • Joined: 16-July 08

    Posted 09 August 2008 - 09:01 PM

    it down do nothing to ur xbox it ur controllor if u dont know what you are doing.